Datalink Associates is proud to introduce the first SDLT (Super Digital Linear Tape) cleaner available on the market. The SDLTa cleaners employ the basic time proven cleaning principles that have been the hallmark of quality tape care. The all new Super DLT cartridge tape cleaners clean, re-tension and optically scan Super DLT and DLT-type cartridges.

The benefit of cleaning your Super DLT and DLT tapes is the assurance that your cartridges are functioning at optimum performance levels. By removing surface debris that interferes with head to tape contact, you greatly reduce dropouts as well as prolong the life of expensive magnetic heads. At 200 ips (inches per second) the SDLTa cleaners can process a SDLT cartridge in less than four (4) minutes, a 1200 foot DLT cartridge in less than three (3) minutes, and a 1828 foot DLT cartridge in less than four (4) minutes.

In one cycle the tape is automatically extracted from the cartridge, wrapped around four (4) automatically advancing tissue stations, cleaned by a sapphire blade (if engaged), optically inspected and then ejected or returned to the magazine ( SDLTa-II ). The automatically advancing cleaning tissue is made of non-shedding nylon material that is placed in such a position, both upstream and downstream of the sapphire cleaning blade, that both sides of the tape are cleaned twice. The cleaning blade, which burnishes the tape, is a precise bi-directional double-edged sapphire blade designed to remove debris adhered to the tape.

The Optical Scanning feature allows you to purge your library of defective cartridges thereby improving the system process time. The optical scanner detects edge damage and tape deformities, such as creases and folds. An indicator on the control panel is provided that counts and displays the number of defects in the tape. In the SDLTa-I tape cleaner, after the tape has been cleaned/inspected, an UP and DOWN scan feature indicates the location of each defect that occurred. A print option (P) can be added to provide the operator with a hard copy of the scan information (defect count and location). On those units with autoloaders ( SDLTa-II ) the user can process a magazine of up to ten (10) SDLT and DLT cartridges at a time for hands-off operation. This option gives the operator a simple PASS/FAIL indicator for each cartridge so that when a magazine of cartridges is completed the status of each cartridge is clearly displayed as PASS or FAIL. If a detailed analysis is required (defect count, position and sequence number) units with an autoloader must have the printer (P) option installed.

Specifications
Drive Speed	200 ips (inches per second) / 5.08 mps (meters per second),
Physical Characteristics
Dimensions (Cleaner only)	15.125" (384 mm) W x 11.00" (279 mm) H x 13.50" (343 mm) D
Dimensions (with Autoloader)	15.125" (384 mm) W x 11.00" (279 mm) H x 24.00" (610 mm) D Note: Does not include magazine or interface plate.
Weight	SDLTa-I : Approximately 30 lbs. (14 Kg), Shipping: 41 lbs. (19 Kg) SDLTa-II : Approximately 45 lbs. (21 Kg), Shipping: 63 lbs. (29 Kg)
Operating Environment
Temperature Range	53.6 ° F to 80.6 ° F (12 ° C to 27 ° C)
Humidity Range	30% to 70% non-condensing
Altitude	7,500 feet (2,286 meters)
Warranty	90 days, part & labor - Return to factory. Phone & e-mail technical assistance for life of machine.
Power	110 to 240 VAC, 48 to 62 Hz, single phase power source

Ordering Information
SDLTa-I SDLTa-II	Single Load SDLT & DLT Cleaner/Inspector SDLTa-I with 10 Cartridge Autoloader Option
Available Options
AA P A M	Audible Alarm (Indicates Eject and End of Cleaning Tissue) Serial Printer (Table Top) with RS232 Serial Interface Autoloader with 10 cartridge magazine (Upgrade) Additional Magazine for Autoloader